Waterborne single component varnishes
Product introduction
1.Single-component, waterborne, polyurethane finish for wood or cork floors, destined for residential/commercial use.
2.For further enhance these features you can add 10% IDRO2 hardener to the paint.
3.The product, catalyzed with IDRO2, is also particularly suited for parquet floors in gymnasiums, because it amply fulfils standard requirements with regard to slipperiness EN 13036-4. Designed for ease of application, the product can be applied by roller, brush or spraying and it is particularly suitable for light wood species (oak, beech, pine, etc.).
Product Application
1.Shake the ACCENT can to dissolve any sediment that has formed on the bottom. In case of catalyzation of the last coat, after shaking the container, pour the varnish into the application container, then add 10% IDRO2 and mix very well. Wait 10-15 minutes before application to allow any foam formed during shaking to dissolve and in the case of the catalyzed product, to allow its pre-airing.
2.Apply a generous coat of product (when using a roller, we recommend Carver MONACO or POSEIDONE), abiding by the times stated for sanding or over coating, in one of the following cycles.
3.For a cycle that will not change the colour of the wood: apply 2 or 3 coats of ACCENT using a roller or brush, always respect the sanding and re-coating times in the table.
4.For a cycle combined with a primer that will not change the colour of the wood: apply 1 or 2 coats of ACCENT in combination with one of the following products used as a primer:
5.FONDO 300 (see technical data sheet)
6.AQUAHIT Mat (see technical data sheet)
7.To carry out a rapid water cycle: apply ACCENT with our FAST water-based primer (see the technical data sheet of this product).
8.Any different cycle or applying method should be previously verified.
9.Use the floor polisher with abrasive pads, grain size #180-220. In case of Trio, use a grain size of 80-100.
10.For spray application with curtain coater or other industrial application method, contact the Carver Technical Assistance Service.
11.WEGCRIL HIDRO ERP 805 is ideal for adhesion on metallic substrates as casted iron, carbon steel and galvanized steel, providing excellent protection for noble autoparts as engine blocks, truck chassis, machinery and equipment and autoparts in general.
12.Apply with spray gun or by imersion. It is environmentally friendly because it is a WATERBORNE PRODUCT, in other words, its solvent is water.
Details
| PAINT FAMILY | Liquid Paint |
| REFERENCIA TINTA LIQUIDA | W-CRIL HIDROERP 80 |
| PAINT PRODUCTS LINE | Water Borne |
| PAINT VERSION | Conventional |
| PAINT FUNCTION | Primer |
| RESIN SYSTEM | Water Borne |
| Solids per volume | Medium Solids |
| SOLIDS VOLUME | 50 ± 2% (ISO 3233 - 1998) |
| Application methods | Airless gun Conventional gun Flooding Immersion |
| Surface preparation | Abrasive blasting to grade Sa 2½ |
| Application surface | Carbon steel |
| Use recommendations | Waterborne acrylic resin single component fast drying primer. Excellent product for coating materials with irregular surfaces as cast iron and blasted carbon steel. Product can be accelerated in oven accordin to client's needs. |
Main characteristics
1. Can withstand high temperature 800-1200℃.
2. Green, zero VOC volatilization, no heavy metals.
3. The coating has high hardness, abrasion resistance, thermal shock resistance and strong bonding force with the matrix.
4. Self-curing at room temperature, strong adhesion with matrix, good anti-corrosion performance, long service life.
Advantages
1.Very low VOC levels (Volatile Organic Compounds), being less aggresive to the environment and the painter
2.Provides highs resistance to corrosion with over 400 hours in salt spray and humid chamber tests
Construction description
After the cleaning of tools, the tools used should be immediately washed with water to prevent drying.
Precautions This product should not be mixed with any oil-based paint or organic solvent.
The paint film shall not be in contact with organic solvents and water before it is completely dried, and shall not be damaged by heavy pressure, bump and friction.
If the second recoating interval is long, it is necessary to sand it to increase the adhesion.
Construction personnel should wear necessary protective equipment.
Store for 12 months (indoor ventilated dry place 5-40℃), beyond this period, can still be used after testing qualified.
Handle with care, avoid bumping and avoid leakage
Packaging specifications According to user requirements, packaging different specifications.
Maintenance
1.Eliminate dust with ANTISTATIC CLOTHS and if necessary, use a vacuum sweeper with non-rotating, natural-fibre bristles, suitable for parquet.
2.For cleaning the parquet, use one of the following options:
Wipe with a soft cloth, soaked in a diluted DETER PARQUET solution (see the technical data sheet) and squeezed. According to the foot traffic the floor is exposed to, follow the wash with a treatment using a diluted solution of our POLISH PARQUET, used as special maintenance treatment (see the technical data sheets).
Wipe with a soft cloth, soaked in a diluted POLISH PARQUET solution, used for frequent/routine maintenance (see the technical data sheet) and squeezed.
Wipe with a soft cloth, soaked in a slightly diluted PRONTO POLISH PARQUET solution (see the technical data sheet) and squeezed.
Notes
1.Acclimatize and apply wood and product at a temperature between +15°C and +35°C. Make sure that the relative humidity in the room is from 35% to 75%.
2.Before application, make sure the hardener is completely dissolved in the finish (there is always a little increase of the mixture viscosity in comparison with the component 1 viscosity). Catalysed paint retains its effectiveness for 4 hours. After this period of time, the paint cannot be used.
3.Always adhere to the prescribed recoating and abrading schedule. When recoating with ACCENT without sanding, do not exceed the 12 hr interval from the previous coat. When sanding and recoating, do not exceed a 5-day interval. Should also this latter interval be exceeded, in order to ensure good adhesion it is necessary to perform careful sanding, wash the floor with a cloth soaked in IDROCLEANER and to add 5% of our DILUENTE GRIP (see the technical data sheet of this product) to the catalyzed finish.
4.After abrading, always vacuum and tack thoroughly.
5.To improve coating or to delay drying, especially in very hot weather, add 5-10% water to the catalysed varnish or 2% of our DILUENTE GRIP.
6.Adhere strictly to the recommended amounts. Matt varnishes tend to become glossy when rubbed, if applied in a very thin layer.
7.Before treating tropical woods or dark woods in general, it is advisable to perform a test beforehand to avoid undesired colour changes.
8.When refinishing old floors, and in all cases in which the wood is very dry, add 10% water to the first coat.
9.The finished surface can be cautiously walked on after 24 hours. It achieves the optimal mechanical resistance after 5-7 days.
Safety and health
Avoid contact with skin and eyes during use. If it comes into contact with skin, it should be quickly wiped off with a cloth and then washed with water. If contact with eyes, rinse with plenty of water and seek medical attention immediately.
Eating, smoking and other unsafe behaviors are prohibited at the construction site; Keep out of reach of children.
Observe all health and safety regulations on site.
FAQ
Q. Are you factory or trading company?
A. We are a factory located in Fuan city, Fujian province, China .
Q. Are all colors are same price?
A.No, the price are different depend on the texture, availability, Ingredients and So on.
Q. Can you provide samples for quality checking before placing an order?
A. Samples are available upon request, but the shipping cost should be paid by customer.
Q. Is there a discount?
A. The discount will be given by the quantity.
Q. How about delivery time?
A. About 7-15 days after payment confirmed.
Q. What kind of payment terms you can accept?
A. We accept T/T, LC, Western Union and Paypal.
